LA1787M
? AM low band cut adjustment method
The AM low band frequency characteristics can be adjusted with C42, which is inserted between pin 42 and V CC .
Since the detector is designed with V CC as the reference, C42 must be connected to V CC .
10
Detector Output — Frequency
Fig.42
VCC
C42
0
0.022 μ F (41pin)
With no used (31pin)
AM
detector
50 k ?
50 k ?
42
10 k ?
10 k ?
+
10 k ?
To pin 31
A12087
–10
–20
–30
0.043 μ F (41pin)
% with no used (31pin)
0.022 μ F (41pin)
With no used (31pin)
0.022 μ F (41pin)
8200 pF (31pin)
Fig. 41
fr = 1000 kHz
fm = 1 kHz, 30%
–40
0.001 2 3 5 70.01 2 3
5 7 0.1
2 3
5 7 1.0
2 3
5 7 10
Frequency — Hz
4. Noise Canceler Block
? The noise canceler input (pin 30) has an input impedance of about 50 k ? . Check the low band frequency
characteristics carefully when determining the value of the coupling capacitor used. Note that f C will be about 3 Hz
when a 1 μF capacitor is used in the application.
? Pins 8 and 9 are used to set the noise detector sensitivity and the noise AGC. It is advisable to first set the noise
sensitivity for a medium field (an antenna input of about 50 dBμ) with pin 8 (the noise sensitivity setting pin), and
then set the AGC level for a weak field (20 to 30 dBμ) with pin 9 (the AGC adjustment pin). If the noise sensitivity
is increased, the AGC will become more effective but, inversely, the weak field sensitivity will be reduced.
Noise canceler 10 kHz overmodulation malfunction may be a problem. In particular, when an overmodulated
signal is input, the noise canceler may, in rare cases, malfunction. This is due to the fact that the IF detector output
has a waveform of the type shown in figure 43 due to the bands of the IF ceramic filters as shown below. (Here, the
antenna input is 60 dBμ, the ceramic filters are 150 kHz × 1 and 180 kHz × 2, f = 10 kHz, 180 kHz dev.) The noise
canceler reacts to the spikes (whiskers) generated due to this overmodulation, which results in distortion to the
audio output. (The spike components due to overmodulation occur due to the bands of the ceramic filters in the
tuner.) The following describes a method for resolving this problem. This incorrect operation due to
overmodulation is prevented by removing the spike components due to this overmodulation with a low-pass filter
consisting of a 1 k ? resistor and a 2200 pF capacitor shown in figure 44. However, note that the FM separation
characteristics in the high band and the AM frequency characteristics will change.
H1 W1
2.5OU
IF audio output
f = 10 kHz,180 kHz dev
IF output
31
1 k ?
Noise canceler input
30
2200 pF
1 μ F
Fig. 44
A12089
–2.5OU
–19.00 μ s
Fig. 43
981.00 μ s
A12088
No. 6655-41/54
相关PDF资料
LAH 100-P SENSOR CURRENT 100A TH
LAH 25-NP SENSOR CURRENT 25A TH
LAH 50-P SENSOR CURRENT 50A TH
LAX 100-NP SENSOR CURRENT 100A 12V TH
LB01KW01-5F24-JF NDICATOR LED SQUARE FOR LB SER
LC01707PLF-TLM-H IC FM DATA TUNER AUTO 44-VQFN
LC104R2K MINITHERMISTORS 100K BETA 4140K
LC1AWT LAMP LC SERIES WHITE
相关代理商/技术参数
LA1787NM 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:Single-Chip Car Radio System IC
LA1787NM_09 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:Single-Chip Car Radio System IC
LA1787NM-MPB-E 制造商:ON Semiconductor 功能描述:ANALOG CAR RADIO TUNER - Trays 制造商:ON Semiconductor 功能描述:FTRAY / ANALOG CAR RADIO TUNER
LA1787NM-TLM-E 制造商:ON Semiconductor 功能描述:ANALOG CAR RADIO TUNER - Tape and Reel 制造商:ON Semiconductor 功能描述:REEL / ANALOG CAR RADIO TUNER
LA17B-10H 制造商:LIGITEK 制造商全称:LIGITEK electronics co., ltd. 功能描述:LED ARRAY
LA17B-5H 制造商:LIGITEK 制造商全称:LIGITEK electronics co., ltd. 功能描述:LED ARRAY
LA1800 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:FM/AM Single-Chip Radio
LA1805 制造商:Panasonic Industrial Company 功能描述:IC